一號仔 asked in 社會與文化語言 · 1 decade ago

Cisco操作步驟翻譯

Step 9 Communicating between a SSH PC (client) to AP (server)

The basic settings to allow a PC and an AP to establish a SSH session are now configured. In order to establish a SSH session, launch the SSH client from the student PC.

a. The configurations will vary among different SSH clients. If PuTTY is being used as the SSH client, following these instructions. Launch the PuTTY.exe file and a pane with various configuration options will open.

b. In the “Host Name (or IP address)” input box enter the IP address of the pod AP. Next, change the protocol to “SSH”. These two values must be sent to establish the SSH. To test the connection, press the Open command button at the bottom of the window.

c. The SSH client will prompt for the local username and password that was previously set on the Pod AP. Enter the “cIsCo123” for the username and “cIsCo123” for the password

d. Was the SSH connection successful? If so, how is the prompt displayed?

Step 10 debug and verify SSH

a. Enable debugging of SSH by entering the following commands

b. SSH debug output

c. Next, open another instance of the SSH client and connect to the AP. Use the correct username and password to log in to the AP. The debug output should be similar to the output below.

d. To get an idea of the debugging process and the debugging message, open another instance of the SSH client and intentionally enter the wrong username or password. View the debugging output for failed authentication.

e. Viewing SSH sessions

f. Use the show ssh command to view the active SSH sessions.

g. Fill in the appropriate values of the table below, based on the output of the show ssh command.

h. To display the version information and SSH parameters, use the show ip ssh command.

i. Is the output displayed exactly as the output below? If not, what are the differences?

專業術語可以不用翻譯 只要能翻譯出每個步驟的意思就好

1 Answer

Rating
  • 1 decade ago
    Favorite Answer

    溝通在SSH個人計算機(客戶)之間的第9步對AP (服務器)

    建立SSH會話現在配置允許個人計算機和AP的基本的設置。 為了建立SSH會話,發射從學生個人計算機的SSH客戶。

    a. 配置在不同的SSH客戶之中將變化。 如果油灰使用作為SSH客戶,從事這些指示。 發射PuTTY.exe文件,并且與各種各樣的配置選項的一塊單塊玻璃將打開。

    b. 在「主機名(或IP地址)」輸入的箱子輸入莢AP的IP地址。 其次,改變協議到「SSH」。 必須送這兩價值建立SSH。 要測試連接,按開放命令按鈕在窗口的底部。

    c. SSH客戶將提示輸入在莢AP以前被設置的地方用戶名和密碼。 輸入「cIsCo123」用戶名的和「cIsCo123」密碼的

    d. SSH連接是否是成功的? 如果那樣,提示怎麼被顯示?

    第10步調試并且核實SSH

    a. 通過輸入以下命令使能SSH調試

    b. SSH調試產品

    c. 其次,打開SSH客戶的另一個事例并且連接到AP。 使用正確用戶名和密碼登錄到AP。 調試產品應該類似下面產品。

    d. 要有調試過程和調試消息的想法,打開SSH客戶的另一個事例和故意地輸入錯誤用戶名或密碼。 觀看為失敗的認證輸出的調試。

    e. 觀察SSH會議

    f. 使用展示ssh命令觀看活躍SSH會議。

    g. 根據展示ssh命令的產品填寫下面桌的適當的價值。

    h. 要顯示版本信息和SSH參量,使用展示ip ssh命令。

    i. 產品正確地被顯示作為下面產品? 否則,有何區别?

    2007-12-23 18:47:45 補充:

    連專業術語都翻譯

    Source(s): 網路
    • Login to reply the answers
Still have questions? Get your answers by asking now.